国外管脚英文资料MB96696管脚资料.pdf

Copyright©2011 FUJITSU SEMICONDUCTOR LIMITED All rights reserved 2011.7 FUJITSU SEMICONDUCTOR DATA SHEET DS704-00011-0v01-E r2.0 16-bit Proprietary Microcontroller CMOS F2MC-16FX MB96690 Series MB96F696* ? DESCRIPTION MB96690 series is based on FUJITSUs advanced 16FX architecture (16-bit with instruction pipeline for RISC-like performance). The CPU uses the same instruction set as the established 16LX series - thus allowing for easy migration of 16LX Software to the new 16FX products. 16FX improvements compared to the previous generation include significantly improved performance - even at the same operation frequency, reduced power consumption and faster start-up time. For high processing speed at optimized power consumption an internal PLL can be selected to supply the CPU with up to 32MHz operation frequency from an external 4MHz resonator. The result is a minimum instruction cycle time of 31.2ns going together with excellent EMI behavior. The emitted power is minimized by the on-chip voltage regulator that reduces the internal CPU voltage. A flexible clock tree allows selecting suitable operation frequencies for peripheral resources independent of the CPU speed. *: These devices are under development and specification is preliminary. These products under development may change its specification without notice. Note: F2MC is the abbreviation of FUJITSU Flexible Microcontroller. For the information for microcontroller supports, see the following website. http:/edevice.fujitsu.com/micom/en-support/ 2 FUJITSU SEMICONDUCTOR CONFIDENTIAL MB96690 Series DS704-00011-0v01-E ? FEATURES ? Technology ? 0.18m CMOS ? CPU ? F 2MC-16FX CPU ? Optimized instruction set for controller applications (bit, byte, word and long-word data types, 23 different addressing modes, barrel shift, variety of pointers) ? 8-byte instruction execution queue ? Signed multiply (16-bit × 16-bit) and divide (32-bit/16-bit) instructions available ? System clock ? On-chip PLL clock multiplier (×1 to ×8, ×1 when PLL stop) ? 4 MHz to 8 MHz external crystal oscillator clock (maximum frequency when using ceramic resonator depends on Q-factor) ? Up to 16 MHz external clock for devices with fast clock input feature ? 32.768 kHz subsystem quartz clock ? 100kHz/2MHz internal RC clock for quick and safe startup, oscillator stop detection, watchdog ? Clock source selectable from mainclock oscillator, subclock oscillator and on-chip RC oscillator, independently for CPU and 2 clock domains of peripherals ? The subclock oscillator is enabled by the Boot ROM program controlled by a configuration marker after a Power or External reset ? Low Power Consumption - 13 operating modes (different Run, Sleep, Timer modes, Stop mode) ? On-chip voltage regulator ? Internal voltage regulator supports reduced internal MCU voltage, offering low EMI and low power consumption figures ? Low voltage reset ? Reset is generated when supply voltage is below minimum ? Code Security ? Protects Flash Memory content from unintended read-out ? DMA ? Automatic transfer function independent of CPU, can be assigned freely to resources ? Interrupts ? Fast Interrupt processing ? 8 programmable priority levels ? Non-Maskable Interrupt (NMI) 3 FUJITSU SEMICONDUCTOR CONFIDENTIAL MB96690 Series DS704-00011-0v01-E ? CAN ? Supports CAN protocol version 2.0 part A and B ? ISO16845 certified ? Bit rates up to 1 Mbit/s ? 32 message objects ? Each message object has its own identifier mask ? Programmable FIFO mode (concatenation of message objects) ? Maskable interrupt ? Disabled Automatic Retransmission mode for Time Triggered CAN applications ? Programmable loop-back mode for self-test operation ? USART ? Full duplex USARTs (SCI/LIN) ? Wide range of baud rate settings using a dedicated reload timer ? Special synchronous options for adapting to different synchronous serial protocols ? LIN functionality working either as master or slave LIN device ? Extended support for LIN-Protocol with 16-byte FIFO for selected channels to reduce interrupt load ? I2C ? Up to 400 kbps ? Master and Slave functionality, 7-bit and 10-bit addressing ? A/D converter ? SAR-type ? 8/10-bit resolution ? Signals interrupt on conversion end, single conversion mode, continuous conversion mode, stop conversion mode, activation by software, external trigger, reload timers and PPGs ? Range Comparator Function ? Scan Disable Function ? ADC Pulse Detection Function ? Source Clock Timers ? Three independent clock timers (23-bit RC clock timer, 23-bit Main clock timer, 17-bit Sub clock timer) ? Hardware Watchdog Timer ? Hardware watchdog timer is active after reset ? Window function of Watchdog Timer is used to select the lower window limit of the watchdog interval ? Reload Timers ? 16-bit wide ? Prescaler with 1/2 1, 1/22, 1/23, 1/24, 1/25, 1/26 of peripheral clock frequency ? Event count function ? Free Running Timers ? Signals an interrupt on overflow ? Prescaler with 1, 1/2 1, 1/22, 1/23, 1/24, 1/25, 1/26, 1/27, 1/28 of peripheral clock frequency ? Input Capture Units ? 16-bit wide ? Signals an interrupt upon external event ? Rising edge, Falling edge or Both (rising FUJITSU SEMICONDUCTOR does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited: Sales Promotion Department