【BS英国标准】BS EN 13164-2001 Thermal insulation products for buildings — Factory made products of extruded polystyrene foam (XPS) — Specification.doc

BRITISH STANDARD BS EN13164:2001IncorporatingAmendment No. 1Thermal insulation products for buildings Factory made products of extruded polystyrene foam (XPS) SpecificationThe European Standard EN 13164:2001, with the incorporation of amendment A1:2004, has the status of a British StandardICS 91.100.60-,-,- Copyright British Standards InstitutionReproduced by IHS under license with BSI - Uncontrolled CopyNo reproduction or networking permitted without license from IHSNot for Resale-,-,-BS EN 13164:2001National forewordThis British Standard is the official English language version of EN 13164:2001, including amendment A1:2004.EN 13164 is a “harmonized” European Standard and fully takes into account the requirements of the European Commission mandate M/103, Thermal insulating materials and products, given under the EU Construction Products Directive (89/106/EEC), and is intended to lead to CE marking. The date of applicability ofEN 13164 as a “harmonized” European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the OfficialJournal of the European Communities.EN 13164 is the subject of transitional arrangements agreed under the European Commission mandate. The Member States have agreed a nominal transition period for the co-existence of EN 13164 and their corresponding national standard(s). It is intended that this period will comprise a nominal nine month period during which any required changes to national regulations are to be made, followed by a further nominal12 month period for the implementation of CE marking. By the end of this co-existence period, any conflicting national standards will be withdrawn or amended to remove conflicts. In the UK, the corresponding national standard is: BS 3837-2:1990, Expanded polystyrene boards Part 2: Specification for extruded boards;and based on this nominal transition period of 21 months, BS 3837-2:1990 will be withdrawn or amended at the latest by March 2003.The UK participation in the preparation of EN 13164:2001 was entrusted to TechnicalCommittee PRI/72, Rigid cellular materials, which has the responsibility to:aid enquirers to understand the text;present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed;monitor related international and European developments and promulgate them in the UK.This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on15 August 2001© BSI 15 July 2004ISBN 0 580 37653 2A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 36, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amd. No.DateComments1525915 July 2004Changes to Clause 2, 4.2.6, Clause 7, D.2,ZA.2.2, Table 9, Table B.2 and Table D.1Amendments issued since publicationEUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORMEN 13164May 2001+ A1May 2004ICS 91.100.60English versionThermal insulation products for buildings Factory made products of extruded polystyrene foam (XPS) Specification (includes amendment A1:2004)Produits isolants thermiques pour le bâtiment Produits manufacturés en mousse de polystyrène extrudé (XPS) Spécification(inclut lamendement A1:2004)Wärmedämmstoffe für Gebäude Werkmäßig hergestellte Produkte aus extrudiertem Polystyrolschaum (XPS) Spezifikation(enthält Änderung A1:2004)This European Standard was approved by CEN on 16 April 2001, and amendment A1 was approved by CEN on 12 February 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I TÉ EUR O P ÉEN DE NO R M AL I S ATI O N EUR O P Ä I S C H ES KOM I T EE F Ü R N O R M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 13164:2001 + A1:2004 E-,-,-Page 2EN 13164:2001ContentsPage-,-,-Foreword.41Scope .52Normative references .63Terms, definitions, symbols, units, abbreviatiated terms .74Requirements .95Test methods.146Designation code.167Evaluation of conformity .168Marking and labelling .17Annex A (normative)Determination of the declared values of thermal resistance and thermal conductivity .18Annex B (normative)Factory production control .20Annex C (normative)Determination of the aged values of thermal resistance and thermalconductivity .23Annex D (informative)Additional properties .27Annex E (informative) Plan for cutting test specimen.29Annex ZA (informative) Clauses of this European Standard addressing the provisions of theEU Construction Products Directive .31TablesTable 1 Tolerances of length, width, squareness and flatness.10Table 2 Classes for thickness tolerances .10Table 3 Levels for compressive stress or compressive strength .11Table 4 Levels for deformation under specified compressive load and temperature conditions .12Table 5 Levels for tensile strength, perpendicular to faces .12Table 6 Levels for long term water absorption by total immersion .13Table 7 Levels for long term water absorption by diffusion .13Table 8 Levels for freeze-thaw resistance .13Table 9 Test methods, test specimens and conditions .15Table A.1 Values of k for one sided 90 % tolerance interval with a confidence level of 90 %.19Table B.1 Minimum product testing frequencies.20Table B.2 Minimum product testing frequencies for the reaction to fire characteristics .21Table D.1 Test methods, test specimens, conditions and minimum testing frequencies .28Table ZA.1 Relevant clauses .32Table ZA.2.1 Systems of attestation of conformity of factory made products for any intended use .33Page 3EN 13164:2001Table ZA.2.2 Systems of attestation of conformity of factory made products for uses subject to regulations on reaction to fire . 34-,-,-Table ZA.3 Example CE marking information. 36Page 4EN 13164:2001ForewordThis European Standard has been prepared by Technical Committee CEN/TC 88, Thermal insulating materials and products, the Secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2001, and conflicting national standards shall be withdrawn at the latest by March 2003.This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this standard. This European Standard contains six annexes.Annex A (normative)Determination of the declared values of thermal resistance and thermal conductivity.Annex B (normative)Factory production control.Annex C (normative)Determination of aged values of thermal resistance and thermal conductivity.Annex D (informative)Additional properties.Annex E (informative)Plan for cutting test specimen.Annex ZA (informative)Clauses of this European Standard addressing the provisions of the EU Construction Products Directive.This European Standard is one of a series of standards for insulating products used in buildings, but this standard may be used in other areas where appropriate.In pursuance of resolution BT 20/1993 revised, CEN/TC88 have proposed defining the standards listed below as a package of European Standards, setting (21 months after availability) as the date of withdrawal (dow) of national standards which conflict with the European Standards of this package.The package of standards comprises the following group of interrelated standards for the specifications of factory made thermal insulation products, all of which come within the scope of CEN/TC88.EN 13162, Thermal insulation products for buildings Factory made mineral wool (MW) products Specification.EN 13163, Thermal insulation products for buildings Factory made products of expanded polystyrene (EPS) Specification.EN 13164, Thermal insulation products for buildings Factory made products of extruded polystyrene foam (XPS) Specification.EN 13165, Thermal insulation products for buildings Factory made rigid polyurethane foam(PUR) products Specification.EN 13166, Thermal insulation products for buildings Factory made products of phenolic foam (PF) Specification.EN 13167, Thermal insulation products for buildings Factory made cellular glass (CG) products Specification.EN 13168, Thermal insulation products for buildings Factory made wood wool (WW) products Specification.-,-,-Page 5EN 13164:2001EN 13169, Thermal insulation products for buildings Factory made products of expanded perlite (EPB) Specification.EN 13170, Thermal insulation products for buildings Factory made products of expanded cork (ICB) Specification.EN 13171, Thermal insulation products for buildings Factory made wood fibre (WF) products Specification.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword to amendment A1This document (EN 13164:2001/A1:2004) has been prepared by Te