Bonded abrasive products- Dimensions.pdf

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 603-1:1999 ICS 25.100.70 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Bonded abrasive products Ð Dimensions Ð Part 1: Grinding wheels for external cylindrical grinding between centres Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 November 1999 BSI 11-1999 ISBN 0 580 35687 6 BS ISO 603-1:1999 Amendments issued since publication Amd. No.DateComments National foreword This British Standard reproduces verbatim ISO 603-1:1999 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper, cloths and powder, which has the responsibility to: Ð aid enquirers to understand the text; Ð present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; Ð monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled ªInternational Standards Correspondence Indexº, or by using the ªFindº facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 16, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m A Reference number ISO 603-1:1999(E) INTERNATIONAL STANDARD ISO 603-1 First edition 1999-07-15 Bonded abrasive products Dimensions Part 1: Grinding wheels for external cylindrical grinding between centres Produits abrasifs agglomérés Dimensions Partie 1: Meules pour rectification cylindrique extérieure entre centres Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) ii Contents Page 1 Scope1 2 Normative references2 3 Dimensions.3 3.1 Type 1: Straight grinding wheel3 3.2 Type 5: Wheel recessed on one side4 3.3 Type 7: Wheel recessed on both sides.6 3.4 Type 20: Wheel relieved on one side8 3.5 Type 21: Wheel relieved on both sides.8 3.6 Type 22: Wheel relieved on one side and recessed on the other side9 3.7 Type 23: Wheel relieved and recessed on one side9 3.8 Type 24: Wheel relieved and recessed on one side and recessed on the other side10 3.9 Type 25: Wheel relieved and recessed on one side and relieved on the other side11 3.10 Type 26: Wheel relieved and recessed on both sides.12 3.11 Type 38: Hubbed wheel13 3.12 Type 39: Double hubbed wheel.13 4 Designation 15 5 Specifications.15 5.1 Tolerances.15 5.2 Balancing.15 5.3 Marking15 Bibliography16 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 603-1 was prepared by Technical Committee ISO/TC 29, Small tools, subcommittee SC 5, Grinding wheels and abrasives. This first edition, together with ISO 603-2:1999 to ISO 603-16:1999, cancels and replaces ISO/R 603:1967, ISO 603-2:1981, ISO 1117:1975, ISO 2220:1972, ISO 2933:1974, ISO 3290:1976 and ISO 3921:1976 as a technical revision of these standards. ISO 603 consists of the following parts, under the general title Bonded abrasive products Dimensions: Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for centreless external cylindrical grinding Part 3: Grinding wheels for internal cylindrical grinding Part 4: Grinding wheels for surface grinding/peripheral grinding Part 5: Grinding wheels for surface grinding/face grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Part 8: Grinding wheels for deburring and fettling/snagging Part 9: Grinding wheels for high-pressure grinding Part 10: Stones for honing and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring and fettling on a vertical grinder Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines Part 16: Grinding wheels for cutting-off on hand held power tools Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m INTERNATIONAL STANDARD ISO 603-1:1999(E) 1 Bonded abrasive products Dimensions Part 1: Grinding wheels for external cylindrical grinding between centres 1 Scope This part of ISO 603 specifies the nominal dimensions, in millimeters, of: Type 1: Straight grinding wheel Type 5: Wheel recessed on one side Type 7: Wheel recessed on both sides Type 20: Wheel relieved on one side Type 21: Wheel relieved on both sides Type 22: Wheel relieved on one side and recessed on the other side Type 23: Wheel relieved and recessed on one side Type 24: Wheel relieved and recessed on one side and recessed on the other side Type 25: Wheel relieved and recessed on one side and relieved on the other side Type 26: Wheel relieved and recessed on both sides. Type 38: Hubbed wheel Type 39: Double hubbed wheel These bonded abrasive products are intended to be used for external cylindrical grinding between centres. The workpiece and the grinding wheel are mechanically guided. Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 2 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 603. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 603 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the lates edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 525:1999, Bonded abrasive products General requirements. ISO 6103:1999, Bonded abrasive products Static balancing of grinding wheels Testing. ISO 13942:1), Bonded abrasive products Limit deviations and run-out tolerances. 1) To be published. Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 3 3 Dimensions 3.1 Type 1: Straight grinding wheel See Figure 1 and Table 1. Figure 1 Type 1 Table 1 Dimensions of Type 1 DTH 20 25 32 40 50 63 80 100 125 150 250 XXXX 076,2 127 300 X X X X X 076,2 127 350/356 400/406 X X X X X X X X X X 127 450/457 X X X X X 127 203,2 500/508 X X X X X 203,2 304,8 600/610 XaXaXaXXXXX 203,2 304,8 750/762 800/813 Xa Xa Xa Xa Xa Xa Xa Xa X X X X X X X X X X 304,8 900/914 XaXaXaXaXXXXX 304,8 406,4 1 060/1 067 XaXaXaXaXaXXXXX 304,8 406,4 1 250 X X X X X 508 a Mainly for camshaft or crankshaft grinding. Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 4 3.2 Type 5: Wheel recessed on one side See Figure 2 and Table 2. Figure 2 Type 5 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 5 Table 2 Dimensions of Type 5 DTHPFRmax 300 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 40 50 63 80 76,2 127 127 203,2 150 190 215 280 13 13 13 25 13 25 3,2 5 500/508 500/508 600/610 600/610 750/762 800/813 900/914 1 060/1 067 1 060/1 067 40 50 63 80 40 50 63 80 63 80 100 63 80 100 63 80 100 63 80 100 63 80 100 63 80 100 125 150 63 80 100 125 150 203,2 304,8 203,2 304,8 304,8 304,8 304,8 304,8 508 400 400 400 400 400 450 450 455 720 13 25 13 25 13 25 50 13 25 50 13 25 50 13 25 50 13 25 50 13 25 50 60 70 13 25 50 60 70 8 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 6 3.3 Type 7: Wheel recessed on both sides See Figure 3 and Table 3. Figure 3 Type 7 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 7 Table 3 Dimensions of Type 7 DTHPFGRmax 300 300 350/356 400/406 450/457 40 50 40 50 40 50 40 50 63 80 76,2 127 127 150 190 215 06 10 6 10 10 10 13 06 10 6 10 10 10 13 3,2 5 5 450/457 500/508 500/508 600/610 600/610 750/762 50 63 80 40 50 63 80 40 50 63 80 50 63 80 100 50 63 80 100 80 100 203,2 203,2 304,8 203,2 304,8 304,8 280 400 400 400 400 10 13 10 13 10 13 10 13 10 13 13 10 13 10 13 10 13 10 13 25 10 13 25 13 25 8 800/813 900/914 1 060/1 067 1 060/1 067 63 80 100 80 100 63 80 100 125 150 63 80 100 125 150 304,8 304,8 304,8 508 450 450 455 720 13 13 13 25 30 13 25 30 13 13 25 13 25 13 25 30 13 25 30 8 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 8 3.4 Type 20: Wheel relieved on one side See Figure 4 and Table 4. Figure 4 Type 20 3.5 Type 21: Wheel relieved on both sides See Figure 5 and Table 4 Figure 5 Type 21 Table 4 Dimensions of Type 20 and Type 21 DTHKNa Rmax 13 16 20 25 32 40 50 63 80 100 125 2° 4° 250XXXXXX 76,2 127 150 190 2 1 4 2 3,2 5 300 300/356 400/406 450/457 X X X X X X X X X X X X X X X X X X X X X X X X X X X 76,2 127 127 127 203,2 150 190 215 215 280 3 2 2 3 4 3 5 4 5 7 8 6 3,2 5 500/508 600/610 750/762 X X X X X X X X X X X X X X X X X X X X 203,2 304,8 203,2 304,8 304,8 400 400 2 4 6 4 7 13 8 a The values N or 2N are taken less than or equal to half thickness T. Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 9 3.6 Type 22: Wheel relieved on one side and recessed on the other side See Figure 6 and Table 5. Figure 6 Type 22 3.7 Type 23: Wheel relieved and recessed on one side See Figure 7 and Table 5. Figure 7 Type 23 Table 5 Dimensions of Type 22 and Type 23 DTHK = PF N Rmax 2° 4° 300 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 40 50 63 80 76,2 127 127 203,2 150 190 215 280 13 13 13 25 13 25 3 3 2 2 2 2 3 3 4 4 3 3 3 3 5 5 4 4 5 5 7 7 8 8 6 6 6 6 3,2 5 500/508 500/508 600/610 600/610 750/762 040 50 63 80 40 50 63 80 63 80 100 63 80 100 63 80 100 203,2 304,8 203,2 304,8 304,8 400 400 400 400 400 13 25 13 25 13 25 40 13 25 40 13 25 40 2 2 2 2 2 2 2 2 4 4 4 4 4 4 6 6 6 4 4 4 4 4 4 4 4 7 7 7 7 7 7 13 13 8 Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 10 3.8 Type 24: Wheel relieved and recessed on one side and recessed on the other side See Figure 8 and Table 6. Figure 8 Type 24 Table 6 Dimensions of Type 24 DTHPFaGaNa Rmax 2° 4° 300 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 50 63 80 76,2 127 127 127 203,2 150 190 215 215 280 6 10 6 10 6 10 13 6 13 6 10 6 10 6 13 6 13 2 3 2 3 2 2 3 3 4 4 3 3 3 4 4 5 5 7 7 8 8 6 6 6 3,2 5 500/508 500/508 600/610 600/610 750/762 40 50 63 80 40 50 63 80 50 63 80 100 50 63 80 100 80 100 203,2 304,8 203,2 304,8 304,8 400 400 400 6 13 6 13 6 13 6 13 13 6 13 6 13 6 13 25 6 13 25 13 25 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 6 6 4 4 4 4 4 4 4 4 7 7 7 7 7 7 13 8 a The values N + F + G are taken less than or equal to half thickness T. Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Sat Sep 09 04:16:00 BST 2006, Uncontrolled Copy, (c) BSI w w w . b z f x w . c o m ISO 603-1:1999(E) 11 3.9 Type 25: Wheel relieved and recessed on one side and relieved on the other side See Figure 9 and Table 7. Figure 9 Type 25 Table 7 Dimensions of Type 25 DTHK = PFaNa Rmax 2° 4° 300 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 40 50 63 80 76,2 127 127 127