BS EN 10055-1996 HOT ROLLED STEEL EQUAL FLANGE TEES WITH RADIUSED ROOT AND TOES. DIMENSIONS AND TOLERANCES ON SHAPE AND DIMENSIONS.pdf

BRITISH STANDARD BS EN 10055:1996 Hot rolled steel equal flange tees with radiused root and toes Dimensions and tolerances on shape and dimensions The Europ an Standard EN 10055:1995 has the status of a British Standard ICS 77.140.70 Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI c BS EN 10055:1996 This British Standard, having been prepared under the direction of the Engineerin Sector Board, was pubhed under the authority of the Standards Board and comes into effect on 15 July 1996 © BSI 06-1999 The following BSI references relate to the work on this standard: Committee reference ISE/13 Draft for comment 92/44027 DC ISBN 0 580 25801 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/13, Structural steel, upon which the following bodies were represented: British Constructional Steelwork Association Ltd. British Iron and Steel Producers Association Health and Safety Executive Amendments issued since publication Amd. No.DateComments Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 10055:1996 i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 100553 Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 10055:1996 National foreword This British Standard has been prepared by Technical Committee ISE/13 and is the English language version of EN 10055:1995 Hot rolled steel equal flange tees with radiused root and toes Dimensions and tolerances on shape and dimensions published by the European Committee for Standardization (CEN). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their rrec application. Compliance with a British Standard does not of itse f conf r immunity from legal obligations. Cross-references Publication referred toCorresponding British Standard EN 10025:1993BS EN 10025:1993 Hot rolled products of nonlloy structural steels. Technical delivery conditions EN 10079:1992BS EN 10079:1993 Definition of steel product Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 1 to 6 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI om EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 10055 November 1995 ICS 77.140.70 Descriptors: Iron and steel products, hot rolled products, T bars, steels, designation, dimensions, dimensional tolerances, form tolerances English version Hot rolled steel equal flange tees with radiused root and toes Dimensions and tolerances on shape and dimensions Fers T en acier à ailes égales et à coins arrondis en acier laminés à chaud Dimensions et tolérances sur la forme et les dimensions Warmgewalzter gleichschenkliger T-Stahl mit gerundeten Kanten und Übergängen Maße, Grenzabaße und Formtoleranzen This European Standard was approved by CEN on 1995-06-30. CEN members are bound to comply with th CEN/CENELEC Internal Regulations which stipulate the conditions fo g ving this European Standard the status of a national standard without any alte ation. Up-to-date lists and bibliogrhical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A ve sion in any other language made by translation under the responsibili of CEN member into its own language and notified to the Central Secr tari has the same status as the official versions. CEN memb r are the national standards bodies of Austria, Belgium, Denmark Finland, France, Germany, Greece, Iceland, Ireland, Italy, Lux mbourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels © 1995 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 10055:1995 E Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ww.bzf w. EN 10055:1995 Foreword This European Standard has been prepared by Technical Committee ECISS/TC11, Structural steel sections, of which the Secretariat is held by BSI. The discussions within ECISS/TC11 were based on Euronorm 55. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1996, and conflicting national standards shall be withdrawn at the latest by May 1996. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Definitions3 4Designation3 5Dimensions3 6Tolerances on dimensions and shape3 7Tolerance on mass3 8Tolerance on length3 Figure 1 Hot rolled steel equal flange tees with radiused root and toes5 Table 1 Designation and dimensions of hot rolled steel equal flange tees with radiused root and to s4 Table 2 Tole ance on dimensions and shape f hot rolled steel equal flange tees with radius root and toes5 Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI w.c EN 10055:1995 3 1 Scope This European Standard specifies requirements for the nominal dimensions and the tolerances on dimensions, shape and mass of hot-rolled steel equal flange tees with radiused root and toes. These requirements do not apply to equal flange tees produced from stainless steel. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10025, Hot rolled products of non alloy structural steels and their technical delivery conditions. EN 10079, Definition of steel products. 3 Definitions For the purpose of this European Standard he definitions given in EN 10079 apply. 4 Designation The designation of the hot-rolled equal flanged tees shall comprise: the term “tee”; the number of this Europ an Standard; the letter T; the height h in mm; number of the qu lity standard and the steel name or steel n mbe of the ordered steel. Example: Tee EN 10055 T 40 steel EN 10025 S 235JR 5 Dimensions Hot-rolled e ual flange tees with radiused root and toes complying with this European Standard shall be produced with the dimensions given in Table 1 and illustrated in Figure 1. 6 Tolerances on dimensions and shape 6.1 Section height (h) The deviation from nominal on section height (h) shall be within the tolerance given in Table 2. 6.2 Flange width (b) The deviation from nominal on flange width (b) shall be within the tolerance give in Table 2. 6.3 Web thickness (s) The deviation from nomi al on w b thickness, when measured at a distancefrom the outer edge of the web shall be withi the tolerance given in Table 2. 6.4 Flange hickness (t) The deviation from nominal on flange thickness when measured at a distance offrom the outer edg of th flange shall be within the tolerance given in T ble 2 6.5 Out of square (k) The out of squareness of the section shall not exceed the maximum given in Table 2. 6.6 Symmetry (e) The tolerance on symmetry shall not be greater than that given in Table 2 where 6.7 Straightness (qxx or qyy) The straightness shall comply with the requirements given in Table 2. 7 Tolerance on mass The mass of a piece shall be within 8 % of the calculated mass for thicknesses 4 mm # s and t # 7 mm (see Table 2) and within 6 % of the calculated mass for s and t 7 mm. The calculated mass shall be determined using a density of 7,85 kg/dm3. 8 Tolerance on length The sections shall be cut to ordered lengths (L) to tolerances in accordance with Table 2. NOTEL represents the longest useable length of the section assuming that the ends of the section have been cut square. h 2 b 4 - e b1b2 2 - -= Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI www om EN 10055:1995 4 © BSI 06-1999 Table 1 Designation and dimensions of hot rolled steel equal flange tees with radiused root and toes DesignationMassCross-sectionDimensionsPosition of centre of gravity Characteristics with respect to the axis HeightWidthThicknessRadiiX XY Y hbs and trr1r2dIxixIyiy kg/mcm2mmcmcm4cm3cmcm4cm3cm T30 T35 T40 T50 T60 T70 T80 T100 T120 T140 1,77 2,33 2,96 4,44 6,23 8,32 10,7 16,4 23,2 31,3 2,26 2,97 3,77 5,66 7,94 10,6 13,6 20,9 29,6 39,9 30 35 40 50 60 70 80 100 120 140 30 35 40 50 60 70 80 100 120 140 4 4,5 5 6 7 8 9 11 13 15 4 4,5 5 6 7 8 9 11 13 15 2 2,5 2,5 3 3,5 4 4,5 5,5 6,5 7,5 1 1 1 1,5 2 2 2 3 3 4 0,85 0,99 1,12 1,39 1,66 1,94 2,22 2,74 3,28 3 80 1,72 3,10 5,28 12 1 23,8 4,5 73,7 179 366 660 0 80 1,23 1, 4 3 36 5,48 8,97 12,8 24,6 42,0 64,7 0,87 1,04 1,18 1,46 1,73 2,05 2,33 2,92 3,51 4,07 0,87 1,57 2,58 6,06 12,2 22,1 37,0 88,3 178 330 0,58 0,90 1,29 2,42 4,07 6,32 9,25 17,7 29,7 47,2 0,62 0,73 0,83 1,03 1,24 1,44 1,65 2,05 2,45 2,88 Ix vx - - Iy vy - - nsed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00 2007, Uncontrolled Copy, (c) BSI .com EN 10055:1995 5 Table 2 Tolerances on dimensions and shape of hot rolled steel equal flange tees with radius d root and toes Figure 1 Hot rolled steel equal flange tees with radiused root and toes 1Cross-sectionNominal dimensionsTolerances on b # 50 50 b # 100 100 b b, h ± 1 ± 1,5 ± 2,0 s,t ± 0,5 ± 0,75 ± 1,0 2Square ess kNominal dimensionsTolerances b,h # 100 100 b,h k # 1 k # 1,5 Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI fx EN 10055:1995 Table 2 Tolerances on dimensions and shape of hot rolled steel equal flange tees with radiused root and toes 3Symmetry e Nominal dimensionsTolerances b # 60 60 b e # 1 e # 1,5 4Length L L represents the longest useable length of the section, assuming that the ends of the section have been cut square. The tolerances required shall be stated in the order. If agreed at the time of enquiry and order, either all plus tolerances or all minus tolerances may be accepted. Tolerances Normal tolerances± 100 Finer tolerances50 ± 25 ± 10 5Straightness qNormal strai htnes he deviation q is measured over the total leng h L of the section N minal dimensionsTolerances 50 # b,h # 100q # 0,4 % of L 6Mass: applicable to individual sectionsThicknessTolerances 4 # s,t # 7 7 s,t 8 % 6 % The deviation in m ss of sections taken individually, is the difference between the supplied mass and the theore ical ass of each section. e b1b2 2 -= Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI wfx . blk Licensed Copy: Institute of Technology Tallaght, Institute of Technology, Wed Nov 07 09:57:36 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 10055:1996 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigu ty while using this British Standard would inform the Secretary of the technil committee responsible, the identity of which can be found on the inside ront over. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standa ds publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international s a da ds, it is BSI policy to supply the BSI implementation of those that have b en published as British Standards, unless otherwise requested. Information on standa ds BSI provides a wide range of i formation on national, European and international standards t rough its Library and its Technical Help to Exporters Service. Various BSI elect onic information services are also available which give details on all its products nd services. Contact the Information Centre. Tel: 020 8996 7111. F x: 0 0 8996 7048. Subscribing mem ers of BSI are kept up to date with standards developments and receive substant al discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, o the publications of the international standardization bodies. Except as p rmitted under the Copyright, Designs and Patents Act 1988 no extract may be r produced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement