BS-EN-60264-3-2-1996 IEC-60264-3-2-1990.pdf

BRITISH STANDARD BS EN 60264-3-2:1996 IEC 264-3-2: 1990 Incorporating Amendment No. 1 BS 7584-3.2:1992 renumbered Packaging of winding wires Part 3: Taper barrelled delivery spools Section 3.2 Specification for returnable spools made from thermoplastic material The European Standard EN 60264-3-2:1994 has the status of a British Standard Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60264-3-2:1996 This British Standard, having been prepared under the direction of the Cables and Insulation Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 August 1992 © BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference CIL/55 Draft announced in BSI News May 1992 ISBN 0 580 21072 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Cables and Insulation Standards Policy Committee (CIL/-) to Technical Committee CIL/55, upon which the following bodies were represented: British Cable Makers Confederation British Non-ferrous Metals Federation British Railways Board Covered Conductors Association EEA (the Association of Electronics, Telecommunications and Business Equipment Industries) Electrical and Electronic Insulation Association Electronic Components Industry Federation Transmission and Distribution Association (BEAMA Ltd.) Amendments issued since publication Amd. No.DateComments 9062May 1996Indicated by a sideline in the margin Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60264-3-2:1996 © BSI 01-2000i Contents Page Committees responsibleInside front cover National forewordii Foreword2 1Scope3 2Normative references3 3Material3 4Type designation3 5Requirements3 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications5 Table 13 Table 24 Table 34 Table 44 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60264-3-2:1996 ii © BSI 01-2000 National foreword This British Standard has been prepared by Technical Committee GEL/55 (formerly CIL/55) and is the English language version of EN 60264-3-2:1994 Packaging of winding wires Part 3: Taper barrelled delivery spools Section 2: Specification for returnable spools made from thermoplastic material, published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC 264-3-2:1990 published by the International Electrotechnical Commission (IEC). BS EN 60264, of which there are four Parts, deals with the packaging of winding wires. Part 1 covers containers, Part 2 covers cylindrical barrelled delivery spools, Part 3 covers taper barrelled delivery spools and Part 4 covers methods of test. This British Standard is one of a series dealing with insulated wires used for windings in electrical equipment, which comprises the following three groups. IEC 851, Methods of test for winding wires. IEC 317, Specifications for particular types of winding wires. IEC 264, Packaging of winding wires. NOTEBS 6811 Winding wires Part 0:1993 General introduction and list of Parts lists the various Sections of BS 6811 and BS 7584 against the corresponding Parts of the IEC standards listed above. Some or all of these IEC standards will be adopted as BS ENs in due course and the relevant Parts of BS 6811 and BS 7584 will be renumbered as BS ENs. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 60264-3-2 December 1994 UDC 621.798.114-036:621.315.337.4 ICS 55.060 Supersedes HD 46.3.2 S1:1992 Descriptors: Winding, electric wire, insulated wire, delivery, spool, packaging, returnable equipment, thermoplastic, designation, specification, marking English version Packaging of winding wires Part 3: Taper barrelled delivery spools Section 2: Specification for returnable spools made from thermoplastic material (IEC 264-3-2:1990) Conditionnement des fils de bobinage Partie 3: Bobines de livraison à fût de forme conique Section 2: Spécification pour les bobines réutilisables, faites de matériau thermoplastique (CEI 264-3-2:1990) Verpackung von Wickeldrähten Teil 3: Lieferspulen mit konischem Kern Hauptabschnitt 2: Spezifikation für Mehrweg-Lieferspulen aus thermoplastischem Werkstoff (IEC 264-3-2:1990) This European Standard was approved by CENELEC on 1994-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels © 1994 Copyright reserved to CENELEC members Ref. No. EN 60264-3-2:1994 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60264-3-2:1994 © BSI 01-2000 2 Foreword The text of the International Standard IEC 264-3-2:1990, prepared by IEC TC 55, Winding wires, was approved by CENELEC as HD 46.3.2 S1 on 1992-06-16. This Harmonization Document was submitted to the formal vote for conversion into a European Standard and was approved by CENELEC as EN 60264-3-2 on 1994-09-01. The following date was fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA is added by CENELEC. latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1995-10-15 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60264-3-2:1994 © BSI 01-20003 1 Scope This International Standard specifies the requirements for returnable taper barrelled delivery spools made from thermoplastic material. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 264-3-1:1989, Packaging of winding wires Part 3: Taper barrelled delivery spools Section 1. Basic dimensions. IEC 264-4-1:1989, Packaging of winding wires Part 4: Methods of test. Section 1 Delivery spools made from thermoplastic material. 3 Material The spools shall be made from thermoplastic material (for example modified polystyrene) that satisfies the requirements given in this standard. The materials used shall not have a deleterious effect on the conductor or the covering of the winding wire. 4 Type designation Taper barrelled delivery spools according to this standard shall be identified by dimensions d1 and l1 as specified in IEC 264-3-1, for example as follows: Delivery spool 264-3-2/IEC 250/400. 5 Requirements For test methods see IEC 264-4-1. 5.1 Spool irregularities 5.1.1 Surface The surface of the spool shall be smooth and the flanges free from protruding material liable to damage the wire or injure the hands of the winding operator. 5.1.2 Construction Bolts and screws, if used in the construction of the spools, shall be countersunk so that the heads are below the surface. 5.2 Spool marking Each spool shall have embossed and/or engraved markings, located on the top side of the upper flange, containing the following information: a) the type designation of the spool (for example 264-3-2/IEC 250/400); b) name and/or trade mark of the spool manufacturer; c) year of manufacture; d) the nominal mass of the spool in grams. The top flange shall be of such design as to allow the application of labels giving details of the manufacturer of the winding wire, its size, the weight of winding wire on the spool, etc. 5.3 Mass The mass of the spool shall comply with the value given in Table 1. There are no requirements for other spools. Table 1 5.4 Spool dimensions The spool dimensions and tolerances shall comply with the dimensions and tolerances given in IEC 264-3-1. 5.5 True running deviations The true running deviations shall not exceed the value given in Table 1 of IEC 264-3-1 (under y and z). 5.6 Behaviour at high temperature The spool shall be conditioned at a temperature of 60 ± 3 °C. The spool dimensions and tolerances shall comply with the dimensions and tolerances given in IEC 264-3-1. No swelling, buckling or variation in the flanges or in the barrel is permitted. 5.7 Impact test on flanges 5.7.1 Under normal ambient conditions The function of the spool shall not be destroyed after stressing with the value given in Table 2. There are no requirements for other spools. Spool type Mass Nominal g Tolerance % 250/400 315/500 400/630 2 250 4 350 7 300 ± 2 ± 2 ± 2 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60264-3-2:1994 4 © BSI 01-2000 Table 2 5.7.2 At low temperature The spool shall be conditioned at a temperature from 10 °C to 12 °C. The function of the spool shall not be destroyed after stressing with 70 % of the value given in Table 2. After conditioning at a temperature of 25 ± 3 °C the spool shall not be destroyed after stressing with 50 % of the value given in Table 2. 5.8 Deformation under load When stressed with the load specified in Table 3, the elongation shall not exceed the value given in Table 3. There are no requirements for other spools. Table 3 5.9 Flexibility test on flanges When stressed with the load specified in Table 4, the increase in distance between the flanges during and after stressing shall not exceed the value given in Table 4. There are no requirements for other spools. Table 4 Spool Type Mass kg Energy N.m 250/400 315/500 400/630 3,0 3,0 3,0 40 45 50 Spool type Minimum tensile load kN Maximum elongation mm 250/400 315/500 400/630 30 50 60 4,0 5,0 6,3 Spool type Load Maximum increase in distance between flanges mm kNDuring stressing After stressing 250/400 315/500 400/630 12,5 20 25 5 7,1 5 0,63 0,63 0,63 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60264-3-2:1994 © BSI 01-20005 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. NOTEWhen the international publication has been modified by CENELEC common modifications, indicated by (mod), the relevant EN/HD applies. IEC publicationDateTitleEN/HDDate 264-3-11989Packaging of winding wires Part 3: Taper barrelled delivery spools Section 1: Basic dimensions EN 60264-3-11994 264-4-11989Part 4: Methods of test Section 1: Delivery spools made from thermoplastic material EN 60264-4-11994 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 6 blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60264-3-2:1996 © BSI 01-2000 List of references See national foreword. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 13 13:31:25 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60264-3-2:1996 IEC 264-3-2: 1990 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Ex