ISO-104-2002.pdf

Reference number ISO 104:2002(E) © ISO 2002 INTERNATIONAL STANDARD ISO 104 Third edition 2002-02-01 Rolling bearings Thrust bearings Boundary dimensions, general plan Roulements Butées Dimensions d'encombrement, plan général Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. © ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii © ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) © ISO 2002 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 104 was prepared by Technical Committee ISO/TC 4, Rolling bearings. This third edition cancels and replaces the second edition (ISO 104:1994). The changes are editorial in order to bring content, terminology and presentation in line with ISO Directives, Part 3, 1997. Annex A of this International Standard is for information only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 104:2002(E) © ISO 2002 All rights reserved 1 Rolling bearings Thrust bearings Boundary dimensions, general plan 1 Scope This International Standard specifies the major boundary dimensions of single-direction and double-direction thrust bearings with flat back faces. In addition, it gives the minimum bore diameters of housing washers and maximum outside diameters of shaft washers of bearings in dimension series 11, 12, 13, 14, 22, 23 and 24. Guidelines for the extension of this International Standard for single-direction thrust bearings are given in annex A. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 582:1995, Rolling bearings Chamfer dimensions Maximum values ISO 1132-1:2000, Rolling bearings Tolerances Part 1: Terms and definitions ISO 5593:1997, Rolling bearings Vocabulary ISO 15241:2001, Rolling bearings Symbols for quantities 3 Terms and definitions For the purposes of this International Standard, the terms and definitions given in ISO 1132-1, ISO 5593 and ISO 15241 apply. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) 2 © ISO 2002 All rights reserved 4 Symbols B height of central shaft washer D outside diameter of housing washer D1 bore diameter of housing washer D1s min smallest single bore diameter of housing washer d bore diameter of shaft washer, single-direction bearing d1 outside diameter of shaft washer, single-direction bearing d1s max largest single outside diameter of shaft washer d2 bore diameter of central shaft washer, double-direction bearing d3 outside diameter of central shaft washer, double-direction bearing d3s max largest single outside diameter of central shaft washer r back face chamfer dimension of shaft washer (single-direction bearing) and housing washer rs min smallest single back face chamfer dimension of shaft washer (single-direction bearing) and housing washer r1 face chamfer dimension of central shaft washer r1s min smallest single face chamfer dimension of central shaft washer T bearing height, single-direction bearing T1 bearing height, double-direction bearing 5 Boundary dimensions 5.1 General The symbols shown in Figures 1 and 2 and the values given in Tables 1 to 9 denote nominal dimensions unless specified otherwise. The corresponding largest single chamfer dimensions to the rs min and r1s min dimensions in Tables 1 to 9 are given in ISO 582. The exact shape of the chamfer surface is not specified, but its contour in an axial plane shall not be allowed to project beyond an imaginary circular arc, of radius rs min, tangential to the washer back face and the bore or outside cylindrical surface of the washer. For the washer face and the bore cylindrical surface, the same applies to r1s min. Chamfer dimensions r and r1 apply only at the corners indicated in Figures 1 and 2. No dimensions are given for other corners, however, they should not be sharp. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) © ISO 2002 All rights reserved 3 5.2 Single-direction thrust bearings Dimensions represented in Figure 1 shall be as given in Tables 1 to 6. Figure 1 Single-direction thrust bearing 5.3 Double-direction thrust bearings Dimensions represented in Figure 2 shall be as given in Tables 7 to 9. Figure 2 Double-direction thrust bearing Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) 4 © ISO 2002 All rights reserved Table 1 Single-direction bearings Diameter series 0 Dimensions in millimetres Dimension series d D rs min 70 90 10 T 4 12 0,3 4 6 6 16 0,3 5 7 8 18 0,3 5 7 10 20 0,3 5 7 12 22 0,3 5 7 15 26 0,3 5 7 17 28 0,3 5 7 20 32 0,3 6 8 25 37 0,3 6 8 30 42 0,3 6 8 35 47 0,3 6 8 40 52 0,3 6 9 45 60 0,3 7 10 50 65 0,3 7 10 55 70 0,3 7 10 60 75 0,3 7 10 65 80 0,3 7 10 70 85 0,3 7 10 75 90 0,3 7 10 80 95 0,3 7 10 85 100 0,3 7 10 90 105 0,3 7 10 100 120 0,6 9 14 110 130 0,6 9 14 120 140 0,6 9 14 130 150 0,6 9 14 140 160 0,6 9 14 150 170 0,6 9 14 160 180 0,6 9 14 170 190 0,6 9 14 180 200 0,6 9 14 190 215 1 11 17 200 225 1 11 17 220 250 1 14 22 240 270 1 14 22 260 290 1 14 22 280 310 1 14 22 300 340 1 18 24 30 320 360 1 18 24 30 340 380 1 18 24 30 360 400 1 18 24 30 380 420 1 18 24 30 400 440 1 18 24 30 420 460 1 18 24 30 440 480 1 18 24 30 Dimensions in millimetres Dimension series d D rs min 70 90 10 T 460 500 1 18 24 30 480 520 1 18 24 30 500 540 1 18 24 30 530 580 1,1 23 30 38 560 610 1,1 23 30 38 600 650 1,1 23 30 38 630 680 1,1 23 30 38 670 730 1,5 27 36 45 710 780 1,5 32 42 53 750 820 1,5 32 42 53 800 870 1,5 32 42 53 850 920 1,5 32 42 53 900 980 2 36 48 63 950 1 030 2 36 48 63 1 000 1 090 2,1 41 54 70 1 060 1 150 2,1 41 54 70 1 120 1 220 2,1 45 60 80 1 180 1 280 2,1 45 60 80 1 250 1 360 3 50 67 85 1 320 1 440 3 95 1 400 1 520 3 95 1 500 1 630 4 105 1 600 1 730 4 105 1 700 1 840 4 112 1 800 1 950 4 120 1 900 2 060 5 130 2 000 2 160 5 130 2 120 2 300 5 140 2 240 2 430 5 150 2 360 2 550 5 150 2 500 2 700 5 160 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) © ISO 2002 All rights reserved 5 Table 2 Single-direction bearings Diameter series 1 Dimensions in millimetres Dimension series d D rs min 71 91 11 T d1s max D1s min 10 24 0,3 6 9 24 11 12 26 0,3 6 9 26 13 15 28 0,3 6 9 28 16 17 30 0,3 6 9 30 18 20 35 0,3 7 10 35 21 25 42 0,6 8 11 42 26 30 47 0,6 8 11 47 32 35 52 0,6 8 12 52 37 40 60 0,6 9 13 60 42 45 65 0,6 9 14 65 47 50 70 0,6 9 14 70 52 55 78 0,6 10 16 78 57 60 85 1 11 17 85 62 65 90 1 11 18 90 67 70 95 1 11 18 95 72 75 100 1 11 19 100 77 80 105 1 11 19 105 82 85 110 1 11 19 110 87 90 120 1 14 22 120 92 100 135 1 16 21 25 135 102 110 145 1 16 21 25 145 112 120 155 1 16 21 25 155 122 130 170 1 18 24 30 170 132 140 180 1 18 24 31 178 142 150 190 1 18 24 31 188 152 160 200 1 18 24 31 198 162 170 215 1,1 20 27 34 213 172 180 225 1,1 20 27 34 222 183 190 240 1,1 23 30 37 237 193 200 250 1,1 23 30 37 247 203 220 270 1,1 23 30 37 267 223 240 300 1,5 27 36 45 297 243 260 320 1,5 27 36 45 317 263 280 350 1,5 32 42 53 347 283 300 380 2 36 48 62 376 304 320 400 2 36 48 63 396 324 340 420 2 36 48 64 416 344 360 440 2 36 48 65 436 364 380 460 2 36 48 65 456 384 400 480 2 36 48 65 476 404 420 500 2 36 48 65 495 424 440 540 2,1 45 60 80 535 444 460 560 2,1 45 60 80 555 464 480 580 2,1 45 60 80 575 484 500 600 2,1 45 60 80 595 504 Dimensions in millimetres Dimension series d D rs min 71 91 11 T d1s max D1s min 530 640 3 50 67 85 635 534 560 670 3 50 67 85 665 564 600 710 3 50 67 85 705 604 630 750 3 54 73 95 745 634 670 800 4 58 78 105 795 674 710 850 4 63 85 112 845 714 750 900 4 67 90 120 895 755 800 950 4 67 90 120 945 805 850 1 000 4 67 90 120 995 855 900 1 060 5 73 95 130 1 055 905 950 1 120 5 78 103 135 1 115 955 1 000 1 180 5 82 109 140 1 175 1 005 1 060 1 250 5 85 115 150 1 245 1 065 1 120 1 320 5 90 122 160 1 315 1 125 1 180 1 400 6 100 132 175 1 395 1 185 1 250 1 460 6 175 1 455 1 255 1 320 1 540 6 175 1 535 1 325 1 400 1 630 6 180 1 620 1 410 1 500 1 750 6 195 1 740 1 510 1 600 1 850 6 195 1 840 1 610 1 700 1 970 7,5 212 1 960 1 710 1 800 2 080 7,5 220 2 070 1 810 1 900 2 180 7,5 220 2 170 1 910 2 000 2 300 7,5 236 2 290 2 010 2 120 2 430 7,5 243 2 420 2 130 2 240 2 570 9,5 258 2 560 2 250 2 360 2 700 9,5 265 2 690 2 370 2 500 2 850 9,5 272 2 840 2 510 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/19/2007 21:30:22 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 104:2002(E) 6 © ISO 2002 All rights reserved Table 3 Single-direction bearings Diameter series 2 Dimensions in millimetres Dimension series d D rs min 72 92 12 T d1s max D1s min 4 16 0,3 6 8 16 4 6 20 0,3 6 9 20 6 8 22 0,3 6 9 22 8 10 26 0,6 7 11 26 12 12 28 0,6 7 11 28 14 15 32 0,6 8 12 32 17 17 35 0,6 8 12 35 19 20 40 0,6 9 14 40 22 25 47 0,6 10 15 47 27 30 52 0,6 10 16 52 32 35 62 1 12 18 62 37 40 68 1 13 19 68 42 45 73 1 13 20 73 47 50 78 1 13 22 78 52 55 90 1 16 21 25 90 57 60 95 1 16 21 26 95 62 65 100 1 16 21 27 100 67 70 105 1 16 21 27 105 72 75 110 1 16 21 27 110 77 80 115 1 16 21 28 115 82 85 125 1 18 24 31 125 88 90 135 1,1 20 27 35 135 93 100 150 1,1 23 30 38 150 103 110 160 1,1 23 30 38 160 113 120 170 1,1 23 30 39 170 123 130 190 1,5 27 36 45 187 133 140 200 1,5 27 36 46 197 143 150 215 1,5 29 39 50 212 153 160 225 1,5 29 39 51 222 163 170 240 1,5 32 42 55 237 173 180 250 1,5 32 42 56 247 183 190 270 2 36 48 62 267 194 200 280 2 36 48 62 277 204 220 300 2 36 48 63 297 224 240 340 2,1 45 60 78 335 244 260 360 2,1 45 60 79 355 264 280 380 2,1 45 60 80 375 284 300 420