ISO-15087-2-2000.pdf
Reference number ISO 15087-2:2000(E) ©ISO 2000 INTERNATIONAL STANDARD ISO 15087-2 First edition 2000-04-15 Dental elevators Part 2: Warwick James elevators Élévateurs dentaires Partie 2: Élévateurs Warwick James Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15087-2:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ©ISO 2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii© ISO 2000 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15087-2:2000(E) © ISO 2000 All rights reservediii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 15087 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15087-2 was prepared by Technical Committee ISO/TC 106,Dentistry, Subcommittee SC 4,Dental instruments. ISO 15087 consists of the following parts, under the general titleDental elevators: ?Part 1: General requirements ?Part 2: Warwick James elevators ?Part 3: Cryer elevators ?Part 4: Coupland elevators ?Part 5: Bein elevators ?Part 6: Flohr elevators Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 15087-2:2000(E) © ISO 2000 All rights reserved1 Dental elevators Part 2: Warwick James elevators 1Scope This part of ISO 15087 gives requirements, including dimensions, for Warwick James dental elevators. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 15087. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 15087 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 1942-3,Dental vocabulary Part 3: Dental instruments. ISO 15087-1:1999,Dental elevators Part 1: General requirements. 3Terms and definitions For the purposes of this part of ISO 15087, the terms and definitions given in ISO 1942-3 apply. 4Design and dimensions 4.1General 4.1.1Warwick James elevators shall conform to the general requirements given in ISO 15087-1. 4.1.2Warwick James elevators shall be grouped into the following types according to the shape of the working end: ?Type 1 = Straight working end ?Type 2 = Left working end ?Type 3 = Right working end 4.1.3Warwick James elevators shall be designed in accordance with Figures 1 and 2, and with dimensions in accordance with Table 1. Measurements of dimensions should be made as defined in Table 2. NOTEAnnex A of ISO 15087-1:1999 provides details of one method of measurement applicable to most types of dental hand instrument. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15087-2:2000(E) 2© ISO 2000 All rights reserved 4.2Length range Warwick James elevators shall have an overall length in the rangebetween 135 mm and 160 mm. 4.3Handle The design and dimensions of the Warwick James elevator handle shall be selected at the discretion of the manufacturer. Table 1 Dimensions of Warwick James elevators Dimensions in millimetres (angular dimensions in degrees) Dimensionsb1b2b3h1l1r1? Tolerance? 0,2? 0,2? 1,0?1,0 refarefa ? 5 Type 1 (Straight)2,21,714,058 Type 2 (Left)2,21,76,04,7581556 Type 3 (Right)2,21,76,04,7581556 a Reference dimension. Table 2 Points of measurement for Warwick James elevators SymbolDesignationPoint of measurement b1Blade width Measured at a distance of 3 mm from the extreme tip of the instrument. b2Blade thickness Measured at a distance of 3 mm from the extreme tip of the instrument. b3Blade length Measured from the farthest extremity of the blade, parallel to the centreline of the blade, to the heel of the blade. h1Blade height Measured from the centreline of the instrument, at right angles to the centreline of the instrument, to the farthest extremity of the blade. l1Working length Measured from the farthest extremity of the blade, parallel to the centreline of the instrument, to the intersection with the handle. r1Radius of blade Radius of curvature of the inner surface of the blade. ?Blade angle Angle between the centreline of the instrument and the centreline of the blade. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15087-2:2000(E) © ISO 2000 All rights reserved3 Dimensions in millimetres Figure 1 Warwick James elevator, straight (type 1) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15087-2:2000(E) 4© ISO 2000 All rights reserved Dimensions in millimetres a) left (type 2)b) right (type 3) Figure 2 Warwick James elevators, left and right 5Designation, labelling and marking If the Warwick James elevator meets the requirements of this part of ISO 15087, then the manufacturer may include in the catalogue, on the package of the product and on the instrument the number of this part of ISO 15087 (ISO 15087-2) followed by an oblique stroke and the number indicating the type of elevator as indicated in 4.1.2. EXAMPLEA Warwick James elevator, type 1, in accordance with this part of ISO 15087 is labelled using the following format: ISO 15087-2/1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15087-2:2000(E) ICS 11.060.20 Price based on 4 pages © ISO 2000 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/24/2007 21:40:15 MDTNo reproduction or networking permitted without license from IHS -,-,-