ISO-15644-2002.pdf
INTERNATIONAL STANDARD ISO 15644 First edition 2002-05-01 Reference number ISO 15644:2002(E) © ISO 2002 Road construction and maintenance equipment Chippings spreaders Terminology and commercial specifications Équipement pour la construction et l'entretien des routes Gravillonneuses Terminologie et spécifications commerciales Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) ii© ISO 2002 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. © ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) © ISO 2002 All rights reserved iii Contents Page 1Scope . 1 2Normative reference . 1 3Terms and definitions 1 4Description of chippings spreader operation 3 4.1Extraction or distribution of chippings from the dumper body bottom 3 4.2Adjustment of chippings flow . 4 4.3Adjustment of spreading width 4 4.4Automatic control by vehicle speed . 4 4.5Diffuser 4 5Commercial specifications 4 5.1Transported chippings spreader 4 5.2Self-propelled chippings spreader . 5 5.3Chippings spreader pushed by tipper truck . 6 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) iv© ISO 2002 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15644 was prepared by Technical Committee ISO/TC 195, Building construction machinery and equipment. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) © ISO 2002 All rights reserved v Introduction This International Standard deals with chippings spreaders used in road construction and surface coating. A chippings spreader is a machine used to spread a layer of chippings on the pavement at a predetermined rate. This International Standard describes the performance characteristics and methods of operation of chippings spreaders and their components. It also provides their definitions and technical characteristics. It includes figures explaining the principles of machine operation and showing the main dimensions related to the machine's performance. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 15644:2002(E) © ISO 2002 All rights reserved 1 Road construction and maintenance equipment Chippings spreaders Terminology and commercial specifications 1Scope This International Standard establishes the terminology and determines the type of technical and commercial specifications for chippings spreaders. This International Standard is applicable to chippings spreaders intended for road construction and surface coating. 2Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, this publication do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. EN 13020, Road-surface treatment machines Safety requirements 3Terms and definitions For the purposes of this International Standard, the following terms and definitions apply. 3.1 chippings spreader machine used to spread a layer of chippings on the pavement at a pre-determined rate NOTEA chippings spreader may be defined by its operating principle. Three types of chippings spreaders may be identified: transported, self-propelled and pushed by tipper truck. 3.2 transported chippings spreader machine equipped with chippings spreading device mounted on the rear of a truck or semi-trailer NOTEThe chippings spreading device can be provided with rollers delivery, see Figure 2 a) or spreading, see Figure 3 a). Chippings may be distributed also from the dumping body bottom by gravity Figure 3 b). 3.3 self-propelled chippings spreader self-propelled machine provided with delivery roller cf. Figure 2 a) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) 2© ISO 2002 All rights reserved 3.4 chippings spreader pushed by tipper truck machine equipped with its own travelling axle and attached to the rear axle of the pushing tipper truck NOTEDelivery roller of the spreader is driven from its travelling axle. 3.5 transport vehicle truck or tractor semi-trailer unit which carries all the components and provides movement of the chippings spreader during spreading and road transfers 3.6 dumping body bin in form of a box for storage of chippings during operation and transport NOTEThe dumping body supplies the chippings spreading device with chippings. It may be equipped with either a scraper shield or conveyor (see Figure 1). 3.7 partial partition of dumping body division wall added in order to improve the distribution of loads over the axle and reducing the load on the chippings spreading device 3.8 chippings spreading device spreading unit mounted on the rear of a tipper truck, and which travels mainly in reverse during work NOTEThe chippings spreading device can be fixed in the place of a tailgate or rear gate of the dumping body. The design of the chippings spreader device is adapted to the vehicle. 3.9 control station assembly which contains the control and adjustment equipment NOTE 1The control station of a transported chippings spreader is typically installed on a platform, which may be fixed or articulated. The controls fulfil the following functions: on-off control of chippings spreading, adjustment of flow blade with or without indicator, adjustment of spreading width, and adjustment of dumper tilt. NOTE 2The control station of a self-propelled chippings spreader contains the controls to move the vehicle forward, supply the storage hoppers and spread the chippings. The control station enables the operator to monitor spreading and usually contains: vehicle operation controls with speedometer and revolutions counter for each roller, the control to unhook the towed truck, conveyors, flow blade, bin gates or slanted blades and expandable hoppers. 3.10 power plant assembly which consists of mechanical components (engine, drive train and driven axles) that contribute to accomplishing the drive function in order to move the chippings spreader during spreading and transfer 3.11 feed system system designed to transport chippings from receiving hopper to spreading hopper NOTEThe receiving hopper receives the chippings discharged by a truck or semi-trailer. The truck of the semi-trailer is coupled to the chippings spreader by means of a rear-mounted tow hook. One or more conveyors may provide transfer of chippings from this hopper to the spreading hopper. The feed system (Figure 9) is composed of a receiving hopper to enable supply of conveyors, and the conveyors which transport the chippings from the receiving hopper to the spreading hopper. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) © ISO 2002 All rights reserved 3 3.12 spreading hopper bin supplied by one or more conveyors, which spreads a defined quantity of chippings on the ground cf. Figure 12 NOTEThe spreading hopper may be equipped with one delivery roller for a fixed width hopper, or multiple rollers or expandable hoppers or moving hoppers. Each delivery roller (1) provided at the hopper base enables regulation of the chippings spreader flow. The roller speed may be automatically controlled by the travel speed of the chippings spreader. The passage of chippings may be regulated by opening the flow blade (2). A feeder (3) ensures a regular fall of chippings on the ground. The spreading width can be adjusted by bin gates or slanting blades (4) for a fixed width hopper, the position of the expandable hoppers and the operation of cut-off plates to vary the width of chippings supplied to the spread roller, thereby varying the width of chippings laid onto the road surface. 3.13 dumping body tilt angle angle of tilt of a dumping body bottom in relation to the horizontal, taken along the longitudinal axis of the vehicle ( in Figure 1) 3.14 dumping body slope angle of a dumping body bottom in relation to the horizontal, taken along the transverse axis of the vehicle ( in Figure 1) 3.15 rear overhang of dumping body distance between the tipping axis and the rear of the dumping body cf. Figure 8 3.16 clearance distance between the ground and the lowest part of a spreader, taken with the dumping body raised cf. Figure 8 4Description of chippings spreader operation 4.1Extraction or distribution of chippings from the dumper body bottom Extraction is undertaken by a roller or by a conveyor (Figure 2) and enables automatic control of the chippings flow by the forward movement speed of the vehicle. Distribution is undertaken by a roller or by gravity (Figure 3). The flow of chippings does not depend on the feeder element, which requires a constant vehicle speed and a constant angle of inclination of the dumping body bottom. For safety requirements for chippings spreaders, see EN 13020. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 19:30:30 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15644:2002(E) 4© ISO 2002 All rights reserved 4.2Adjustment of chippings flow The adjustment of chippings flow per unit of width is illustrated in Figure 4. The flow blade (or register) enables adjustment of the thickness of the stream of chippings. Adjustment may be undertaken either by using a flow blade or a stop on the bin gates, or by adjusting the speed of the roller or conveyor. 4.3Adjustment of spreading width This adjustment may be undertaken either by the bin gates or by slanting blades (Figure 5). 4.4Automatic control by vehicle speed In order to obtain a constant proportion of chippings on the ground, the roller speed, or the conveyor speed, or the opening of the flow blade may be linked to the vehicle speed unless the latter is kept absolutely constant. 4.5Diffuser A simple diffuser (Figure 6) typically has the following forms: smooth or partitioned; flat or curved. A diffuser with built-in or separate distributor (Figure 7) may be equipped on each side with a folding flap extension so that the spreading width will then be greater than the vehicle width. 5Commercial specifications 5.1Transported chippings spreader 5.1.1Main assemblies These shall be as shown in Figure 1: transporting vehicle; dumping body; chippings spreading device; control station; partial partition. 5.1.2Dimensional char
