ISO-15875-1-AMD-1-2007.pdf

Reference number ISO 15875-1:2003/Amd.1:2007(E) © ISO 2007 INTERNATIONAL STANDARD ISO 15875-1 First edition 2003-12-01 AMENDMENT 1 2007-06-15 Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 1: General AMENDMENT 1 Systèmes de canalisations en plastique pour les installations d'eau chaude et froide Polyéthylène réticulé (PE-X) Partie 1: Généralités AMENDEMENT 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 06/19/2007 00:13:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15875-1:2003/Amd.1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT © ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii © ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 06/19/2007 00:13:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15875-1:2003/Amd.1:2007(E) © ISO 2007 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO 15875-1:2003 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 06/19/2007 00:13:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15875-1:2003/Amd.1:2007(E) iv © ISO 2007 All rights reserved Introduction In ISO 15875-2:2003, the base pipe is required to fulfil the dimensional requirements and the barrier is an “add on” giving to the finished product a wall thickness and outside diameter greater than stated in that part of ISO 15875. In some countries it is common practice that the finished product be required to fulfil the dimensional requirements of the standard. This situation creates a problem throughout the world due to different requirements in different countries. It illustrates the need to have a common procedure on the market for dealing with this matter. ISO 15875-2:2003/Amd. 1:2007 was developed to clarify the requirements on dimensions and tolerances for barrier pipes and create a common procedure for designing and testing those pipes. Amendment 1 to ISO 15875-1:2003 clarifies the definition of the term pipes with barrier layer and supplements ISO 15875-2:2003/Amd. 1:2007. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 06/19/2007 00:13:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15875-1:2003/Amd.1:2007(E) © ISO 2007 All rights reserved 1 Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 1: General AMENDMENT 1 Page 4, 3.1.4 Replace the definition of the term with the following: 3.1.4 pipes with barrier layer plastics pipes provided with a thin barrier layer (e.g. to prevent or greatly diminish the diffusion of gases and the transmission of light through the pipe wall) and where the design stress requirements are totally met by the base polymer NOTE Such pipes typically have an outside (barrier) layer of maximum 0,4 mm thickness, including any adhesive. Pipes with an outside layer greater than 0,4 mm are considered as multilayer pipes (see Bibliographic references 5 to 8), with the outside layer then being the first of multiple layers rather than having only a barrier function. Page 8, Bibliography Add the following to the Bibliography: 5 ISO 21003-11), Multilayer piping systems for hot and cold water installations inside buildings Part 1: General 6 ISO 21003-21), Multilayer piping systems for hot and cold water installations inside buildings Part 2: Pipes 7 ISO 21003-31), Multilayer piping systems for hot and cold water installations inside buildings Part 3: Fittings 8 ISO 21003-51), Multilayer piping systems for hot and cold water installations inside buildings Part 5: Fitness for purpose of the system 1) To be published. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 06/19/2007 00:13:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15875-1:2003/Amd.1:2007(E) ICS 23.040.01; 91.140.60 Price based on 1 page © ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 06/19/2007 00:13:31 MDTNo reproduction or networking permitted without license from IHS -,-,-