ISO-11001-2-1993.pdf

INTERNATIONAL STANDARD IS0 11001-2 First edition 1993-l o-07 Agricultural wheeled tractors and implements - Three-point hitch couplers - Part 2: A-frame coupler Tracteurs agricoles 9 roues et instruments - Coupleurs rapides trois points - Partie 2 Coupleur par cadre en A - - = giggc z =,$.I Reference number IS0 11001-2 1993(E) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 11001-2:1993(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote International Standard IS0 11001-2 was prepared by Technical Committee lSO/TC 23, Tractors and machinery for agriculture and forestry, Sub- Committee SC 4, Tractors. IS0 11001 consists of the following parts, under the general title Agricul- tural wheeled tractors and implements - Three-point hitch couplers. - Part 1. U-frame coupler - Part 2: A-frame coupler - Part 3: Link coupler - Part 4. Bar coupler 0 IS0 1993 All rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without per- mission in writing from the publisher International Organization for Standardization Case Postale 56 ? CH-1211 Geneve 20 ? Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD IS0 IlOOl-2:1993(E) Agricultural wheeled tractors and implements - Three-point hitch couplers - Part 2: A-frame coupler 1 Scope This part of IS0 11001 specifies the essential dimen- sions for the attachment of three-point hitch im- plements to agricultural wheeled tractors equipped with a three-point free link hitch according to IS0 730-l or IS0 8759-2, and an A-frame hitch cou- pler. NOTE 1 In general the dimensions associated with the tractor and the implement for use with hitch couplers are the same as those for the three-point linkage specified in IS0 730-I or IS0 8759-2, and those for the clearance zone specified in IS0 23321). The three-point hitch coupler systems constitute a special method of implement mounting. The hitch couplers are an additional component located be- tween the three-point linkage and the implement, making it possible to hitch and unhitch from the op- erator s seat Due to the special construction and function of hitch couplers, it may be necessary to vary the length of the links indicated in the referenced standards. This part of IS0 11001 applies to category 2 of agri- cultural wheeled tractors as defined in IS0 730-I. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 11001. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 11001 are encouraged to investi- gate the possibility of applying the most recent edi- tions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards IS0 730-I : 1990, Agricultural wheeled tractors - Rear-mounted three-point linkage - Part 1. Catego- ries I, 2 and 3. IS0 8759-2:1985, Agricultural wheeled tractors - Front-mounted linkage and power take-off - Part 2. Front linkage. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 11001-2:1993(E) 3 Principle of frame coupler system A frame coupler system is a one-phase implement coupler where the three-point linkage of the tractor (see IS0 730-I or IS0 8759-2) is fitted with an A- frame and the implement has the frame incorporated into the mast. Hitching and unhitching can be carried out from the tractor operator s seat (see figure I). Figure 1 - Principle of A-frame coupler 1 For information only. 4 Dimensions Dimensions shall comply with figures 2 and 3 5 Requirements associated with implement 5.1 Clearance zones Clearance zones shall comply with figure 3. The necessary clearance zones and the height pos- itions of the mast for executing hitching and unhitch- ing are indicated by a dash-point line 5.2 Locking device A positive latch shall be provided to prevent uninten- tional separation of the implement. Dimensions in millimetres Implement frame Tractor frame ) Figure 2 - Dimensions for coupler associated with implement Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 11001-2:1993(E) Dimensions in millimetres General tolerance: -+ 0,l W s I =-v-P-i X A r , y ,./j;,. . . 'y i! jp jx ) / / ! / 1 5i6 I ? '0 C' z 'g c ! .I I- 0 I 1196 3 i-.-A i-r I i.-.-. *) See detail X. ? *) Adjustable lip to maintain dimension 136 mm. *I Path of locking device. Figure 3 - Dimensions and clearance zone for implement frame and locking device 3 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 11001-2:1993(E) UDC 631.372:621.838.2 Descriptors: agricultural machinery, tractors, agricultural tractors, couplings, rigid couplings, specifications, dimensions. Price based on 3 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/26/2007 02:38:33 MDTNo reproduction or networking permitted without license from IHS -,-,-