ISO-21138-2-2007.pdf

Reference number ISO 21138-2:2007(E) © ISO 2007 INTERNATIONAL STANDARD ISO 21138-2 First edition 2007-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Pipes and fittings with smooth external surface, Type A Systèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement sans pression enterrés Systèmes de canalisations à parois structurées en poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) Partie 2: Tubes et raccords avec une surface externe lisse, type A Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 21138-2:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT © ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii © ISO 2007 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 21138-2:2007(E) © ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms, definitions, symbols and abbreviated terms. 3 3.1 Terms and definitions. 3 3.2 Symbols. 4 3.3 Abbreviated terms 4 4 Material 5 4.1 General. 5 4.2 Unplasticized poly(vinyl chloride) (PVC-U) 5 4.3 Polypropylene (PP). 6 4.4 Polyethylene (PE) 8 5 Designation of wall construction and examples of typical jointing methods 10 5.1 Wall constructions designated as Type A 10 5.2 Designation and design of joints 12 6 General characteristics for pipes and fittings Colour 12 7 Geometrical characteristics. 12 7.1 General. 12 7.2 Dimensions 12 7.3 Types of fitting 17 8 Physical characteristics. 17 8.1 Unplasticized poly(vinyl chloride) (PVC-U) 17 8.2 Polypropylene (PP). 19 8.3 Polyethylene (PE) 19 9 Mechanical characteristics 20 9.1 Mechanical characteristics of pipes. 20 9.2 Mechanical characteristics of fittings. 23 10 Performance requirements 23 11 Marking 25 11.1 General. 25 11.2 Minimum required marking 25 Annex A (normative) Virgin PVC-U material 27 Annex B (normative) Utilization of non-virgin PVC-U material 28 Annex C (normative) Virgin PP material 31 Annex D (normative) Utilisation of non-virgin PP material 32 Annex E (normative) Virgin PE material 35 Annex F (normative) Utilization of non-virgin PE material 36 Annex G (informative) Survey of possible use of reprocessable and recyclable material. 40 Bibliography. 41 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 21138-2:2007(E) iv © ISO 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21138-2 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). ISO 21138 consists of the following parts, under the general title Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): Part 1: Material specifications and performance criteria for pipes, fittings and system Part 2: Pipes and fittings with smooth external surface, Type A Part 3: Pipes and fittings with non-smooth external surface, Type B Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 21138-2:2007(E) © ISO 2007 All rights reserved v Introduction ISO 21138 is the system standard covering the plastics piping systems for non-pressure underground drainage and sewerage, in particular thermoplastics structured-wall piping systems. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 21138-2:2007(E) © ISO 2007 All rights reserved 1 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Pipes and fittings with smooth external surface, Type A 1 Scope This part of ISO 21138, together with ISO 21138-1, specifies the definitions and requirements for pipes with a smooth external surface (Type A), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping in the field of non-pressure systems for underground drainage and sewerage. NOTE 1 These pipes, fittings and the system can be used for highway drainage and surface water. This part of ISO 21138 specifically refers to PVC, PP and PE materials. NOTE 2 Other thermoplastic materials can be added via an addendum. This part of ISO 21138 specifies test methods and test parameters. This part of ISO 21138 covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with ISO 21138-1, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewage. It is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. NOTE 4 For dimensions larger than DN/OD 1200, or DN/ID 1200, this part of ISO 21138 can serve as a general guide regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. Test methods are not included in this document. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 21138-2:2007(E) 2 © ISO 2007 All rights reserved ISO 178, Plastics Determination of flexural properties ISO 306:1994, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) ISO 527-2:1993, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics ISO 580:2005, Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating ISO 1133:2005, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces ISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method ISO 2505, Thermoplastics pipes Longitudinal reversion Test methods and parameters ISO 2507-1, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 2507-2, Thermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC-Hi) pipes ISO 3126, Plastics piping systems Plastics components Determination of dimensions ISO 3127:1994, Thermoplastics pipes Determination of resistance to external blows Round-the-clock method ISO 3451-1:1997, Plastics Determination of ash Part 1: General methods ISO 4435:2003, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) ISO 8772:2006, Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) ISO 8773:2006, Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method ISO 9967, Thermoplastics pipes Determination of creep ratio ISO 9969, Thermoplastics pipes Determination of ring stiffness ISO 11173:1994, Thermoplastics pipes Determination of resistance to external blows Staircase method ISO 11357-6, Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=leee, leee Not for Resale, 11/22/2007 20:10:13 MSTNo reproduction or networking permitted without license from IHS -,-,- ISO 21138-2:2007(E) © ISO 2007 All rights reserved 3 ISO 21138-1, Plastics piping systems for non-pressure underground drainage and sewerage Structured- wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and the system ISO 21138-3, Plastics piping systems for non-pressure underground drainage and sewerage Structured- wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Pipes and fittings with a non-smooth external surface, Type B ISO 22088-3, Plastics Determination of resistance to environmental stress cracking (ESC) Part 3: Bent strip method EN 922, Plastics piping and ducting systems Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) Specimen preparation for determination of the viscosity number and calculation of the K-value EN 1053, Plastics piping systems Thermoplastics piping systems for non-pressure applications Test method for watertightness EN 1277:2003, Plastics piping systems Thermoplastics piping systems for buried non-pressure applications Test methods for leaktightness of elastomeric sealing ring type joints EN 1437:2002, Plastics piping systems Piping systems for underground drainage and sewerage Test method for resistance to combined temperature cycling and external loading EN 1446, Plas