ISO-9159-1988.pdf
INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXJJYHAPOAHAFI OPrAHM3AklR IlO CTAHAPTM3AWl Road vehicles - Nozzle spouts for leaded gasoline and diesel fuel Whicules rou tiers - Pistolets de remplissage pour essence au plomb et carburant diesel IS0 9159 First edition 1988-04-01 Reference number IS0 9159: 1988 (E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. They are approved in accordance with IS0 procedures requiring at least 75 % approval by the member bodies voting. International Standard IS0 9159 was prepared by Technical Committee ISO/TC 22, Road vehicles. Users should note that all International Standards undergo revision from time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated. 0 International Organization for Standardization, 1988 l Printed in Switzerland -,-,- INTERNATIONAL STANDARD IS0 9159 : 1988 (E) Road vehicles - Nozzle spouts for leaded gasoline and diesel fuel 1 Scope and field of application This International Standard specifies the dimensions of nozzle spouts on pumps for refuelling road vehicles, and their filling rates. It applies to nozzle spouts for leaded gasoline and diesel fuel for road vehicles. 2 Reference IS0 4130, Road vehicles - Three-dimensional reference systems and fiducial marks - Definitions. 3 Requirements The nozzle spout shall conform to the dimensions given in the figure. The shape is at the manufacturers discretion. The flow rate, qv, shall be qv 50 Vmin for leaded gasoline; qv 50 Vmin or 50 Vmin qv 100 Vmin for diesel fuel, depending on spout dimensions (see the figure). The figure shows a nozzle spout with a spring for safe hooking in the tank filler opening. The dimensions apply also to nozzle spouts with cams or depressions for safe hooking. IsO9159:1988 (El Dimensions in millimetres Cams, depressions or spring at the manufacturers discretion Dimension Symbol Description qv G 50 Vmin (leaded gasoline or diesel fuel) 50 Vmin q+ 100 Vmin (diesel fuel) Nozzle outside diameter 23,6 min. 25.5 max. 32 max. D2 1 Anchor spring outside diameter I 30 max. I 38 max. I 1 Length of straight part of nozzle pipe I 80 to 95 I 65 to 90 I Distance between nozzle end and anchor spring cam LlL295 90 to 110 L3 I Distance between nozzle end and sensor I 22 max. I 22 max. I L4 1 Clearance from fuel dispensing end to any part of nozzle body I 165 min. I 170 to 200 I r 1 Nozzle pipe bending radius I 100 to 250 I 120 to 160 I 1 Bending angle of nozzle pipe I 21° I!I 1,5O I 21° 5 1,5O I Figure 1) Nozzle spout shown in its hooked filling position, and angle towards Z plane according to IS0 4130. UDC 621 l 3.06 : 62-225 : 656.062 : 665.733.5 + 665.753.41 : 629.113 Descriptors : refuelling, gasoline, diesel fuels, fuel handling equipment, nozzles, dimensions. Price based on 2 pages -,-,-