SAE-AS-125851-THRU-AS-125875B-2007.pdf
AEROSPACE STANDARD (R) PLUG - PIPE, CADMIUM PLATED, STEEL UNS G87400, COUNTERSUNK HEX AS125851 THRU AS125875 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1953-01 REAFFIRMED 2006-08 REVISED 2007-05 THIRD ANGLE PROJECTION CUSTODIAN: SAE E-25 REV. B FEDERAL SUPPLY CLASS 5307 AS125851 THRU AS125875 SHEET 1 OF 2 REV. B PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE UPDATE STANDARD, CHANGE PIPE THREAD TO AS71051, AND ADD CADMIUM WARNING NOTE. SECTION THRU THREAD PROFILE BOTH ENDS 32 F C L CHAMFER Y x 45 APPROX OPPOSITE END OPTIONAL o B SHAPE OF SOCKET BOTTOM OPTIONAL. DRILL POINT PERMISSIBLE. SHALL BE WITHIN DIMENSIONS SHOWN AND FREE FROM CHIPS AND BURRS. THREAD ANPT SPEC AS71051 D FIGURE 1 - PLUG TABLE 1 - PART NUMBERS AND DIMENSIONS PART NUMBER NOMINAL PIPE THREAD B MIN C MIN D L F MAX Y AS125851 AS125852 AS125853 AS125854 AS125855 AS124856 AS125857 AS125858 .0625-27 .125-27 .250-18 .375-18 .500-14 .750-14 1.000-11.5 1.250-11.5 .094 .094 .125 .125 .125 .125 .125 .125 .094 .125 .219 .219 .375 .375 .438 .500 .1563 - .1582 .1875 - .1895 .2500 - .2520 .3125 - .3155 .3750 - .3780 .5625 - .5655 .6250 - .6290 .7500 - .7540 .260 - .280 .260 - .280 .400 - .420 .400 - .420 .530 - .550 .540 - .560 .680 - .700 .700 - .720 .188 .244 .326 .400 .463 .681 .775 1.072 .020 - .050 .020 - .050 .030 - .060 .030 - .060 .050 - .080 .050 - .080 .060 - .090 .060 - .090 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:25:33 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) PLUG - PIPE, CADMIUM PLATED, STEEL UNS G87400, COUNTERSUNK HEX AS125851 THRU AS125875 REV. B AS125851 THRU AS125875 SHEET 2 OF 2 REV. B NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUM'S USE. 1. MATERIAL: LOW ALLOY STEEL PER AMS 6322 (UNS G87400). 2. HARDNESS: 26-32 HRC. HARDEN (OR OIL QUENCH) AND TEMPER. 3. FINISH: CADMIUM PLATE PER AMS 2400. 4. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 250 MICROINCHES Ra. 6. MARK PART NUMBER AND MANUFACTURERS IDENTIFICATION ON CONTAINER. 7. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 8. DIMENSIONS ARE IN INCHES. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. THE CHANGE BAR ( I ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:25:33 MSTNo reproduction or networking permitted without license from IHS -,-,-
