SAE-AS-39029-29A-2007.pdf

AEROSPACE STANDARD (R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE (FOR AS50151 SERIES, AS34501 AND MIL-DTL-83723 SERIES 2 CONNECTORS) AS39029/29 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-03 REVISED 2007-07 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C1 REV. A FEDERAL SUPPLY CLASS 5999 AS39029/29 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS39029 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE REVISE TO INCLUDE COMMENTS RECEIVED BY THE GOVERNMENT AND INDUSTRY SINCE 1988, INCORPORATES VARIOUS AMENDMENTS, REMOVE GOVERNMENT JARGON AS A RESULT OF THE WORD-FOR-WORD TRANSFERENCE OF AS39029 TO SAE, UPDATE SPECIFICATION REFERENCES, ALIGN SPECIFICATIONS WITH SAE GUIDELINES AS NEEDED, AND REVIEW SPECIFICATIONS FOR KNOWN TECHNICAL PROBLEMS. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF: SAE AS39029. MATING PIN SIZES 16, 0 CONTACTS AND ALL WIRE BARREL SIZES MATING PIN SIZES 12, 8, 4 CONTACTS FIGURE 1 - AS39029/29 PIN CONTACT Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:28:44 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE (FOR AS50151 SERIES, AS34501 AND MIL-DTL-83723 SERIES 2 CONNECTORS) AS39029/29 REV. A AS39029/29 SHEET 2 OF 3 REV. A TABLE 1 - CONTACT DIMENSIONS TABLE 2 - MARKING AND DESIGN CHARACTERISTICS COLOR BANDS BIN CODES 1ST 2ND 3RD MATING END SIZE WIRE BARREL SIZE TYPE CLASS 212 RED BROWN RED 16 16 A B 213 RED BROWN ORANGE 12 12 A B 214 RED BROWN YELLOW 8 8 A B 215 RED BROWN GREEN 4 4 A B 216 RED BROWN BLUE 0 0 A B TABLE 3 - TOOL REQUIREMENTS BIN CODE BASIC CRIMPING TOOL DIE SET LOCATOR POSITIONER INSTALLING TOOL REMOVAL TOOL M22520/1-01 N/A N/A M22520/1-02 BLUE 212 M22520/7-01 N/A N/A M22520/7-03 M81969/14-03 M81969/14-03 213 M22750/1-01 N/A N/A M22520/1-02 YELLOW M81969/14-04 M81969/14-04 214 M22520/23-01 M22520/23-02 M22520/23-09 N/A N/A M81969/29-02 215 M22520/23-01 M22520/23-04 M22520/23-11 N/A N/A M81969/29-03 216 M22520/23-01 M22520/23-05 M22520/23-13 N/A N/A M81969/29-04 TABLE 4 - PART NUMBERS AS39029 PART NUMBER BIN CODE SUPERSEDES PART NUMBER(S) M39029/29-212 212 M39029/29-16-16 M39029/29-213 213 M39029/29-12-12 M39029/29-214 214 M39029/29-8-8 M39029/29-215 215 M39029/29-4-4 M39029/29-216 216 M39029/29-0-0 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:28:44 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE (FOR AS50151 SERIES, AS34501 AND MIL-DTL-83723 SERIES 2 CONNECTORS) AS39029/29 REV. A AS39029/29 SHEET 3 OF 3 REV. A REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST HEREIN AND AS39029. 1. DESIGN: CONTACT SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1, TABLES 1 AND 2. DIMENSIONS ARE IN INCHES AND SHOWN AFTER PLATING. UNLESS OTHERWISE SPECIFIED, SPHERICAL END DIMENSIONS SHALL CONFORM TO AS39029. ALL DIMENSIONS PROVIDED IN PARENTHESES ARE METRIC EQUIVALENTS AND GIVEN FOR GENERAL INFORMATION ONLY (SEE AS39029 SECTION 6). 2. TOOLS: TOOLS REQUIRED FOR CRIMPING CONTACTS TO WIRE/CABLE AND THE INSTALLING/REMOVAL FROM THE CONNECTOR SHALL BE IN ACCORDANCE WITH TABLE 3. 3. PART NUMBERS: CONTACT PART NUMBERS SHALL BE IN ACCORDANCE WITH TABLE 4. SUPERSEDING PART NUMBERS ARE AS SPECIFIED. 4. MATERIALS: MATERIALS SHALL BE IN ACCORDANCE WITH AS39029. 5. MECHANICAL: MECHANICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. 6. ELECTRICAL: ELECTRICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. 7. ENVIRONMENTAL: ENVIRONMENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029 SHOCK TEST SHALL BE PERFORMED AT TEST CONDITION A. 8. APPLICATION NOTES: CONTACT MATES DIRECTLY INTO AN AS39029/30 SOCKET AS SHOWN TABLE 5. BIN CODE 214, 215, AND 216 ARE NOT RECOMMENDED FOR NAVY SHIPBOARD APPLICATION. TABLE 5 - CONTACT MATING PART NUMBERS AS39029/29 BIN CODE MATING AS39029/30 BIN CODE 212 217 212 218 213 219 214 220 215 221 216 222 9. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:28:44 MSTNo reproduction or networking permitted without license from IHS -,-,-