ISO-8861-1998.pdf
《ISO-8861-1998.pdf》由会员分享,可在线阅读,更多相关《ISO-8861-1998.pdf(18页珍藏版)》请在三一文库上搜索。
1、A Reference number ISO 8861:1998(E) INTERNATIONAL STANDARD ISO 8861 Second edition 1998-05-15 Shipbuilding Engine-room ventilation in diesel-engined ships Design requirements and basis of calculations Construction navale Ventilation du compartiment machines des navires moteurs diesels Exigences de c
2、onception et bases de calcul ISO 8861:1998(E) ISO 1998 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publis
3、her. International Organization for Standardization Case postale 56 CH-1211 Genve 20 Switzerland Internetcentraliso.ch X.400c=ch; a=400net; p=iso; o=isocs; s=central Printed in Switzerland ii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national stan
4、dards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International org
5、anizations, governmental and non- governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are
6、 circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 8861 was prepared by Technical Committee ISO/TC 8, Ships and marine technology, Subcommittee SC 3, Piping and machi
7、nery. This second edition cancels and replaces the first edition (ISO 8861:1988), of which it constitutes a technical revision. Annex A of this International Standard is for information only. INTERNATIONAL STANDARD ISOISO 8861:1998(E) 1 Shipbuilding Engine-room ventilation in diesel-engined ships De
8、sign requirements and basis of calculations 1 Scope This International Standard specifies design requirements and suitable calculation methods for the ventilation of the engine room in diesel-engined ships, for normal conditions in all waters. Annex A provides guidance and good practice in the desig
9、n of ventilation systems for ships engine rooms. NOTE Users of this International Standard should note that, while observing the requirements of the standard, they should at the same time ensure compliance with such statutory requirements, rules and regulations as may be applicable to the individual
10、 ship concerned. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreeme
11、nts based on this Interna- tional Standard are encouraged to investigate the possibility of applying the most recent editions of the standards listed below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 31-1:1992, Quantities and units Part 1: Space and tim
12、e. ISO 31-3:1992, Quantities and units Part 3: Mechanics. ISO 31-4:1992, Quantities and units Part 4: Heat. ISO 3046-1:1995, Reciprocating internal combustion engines Performance Part 1: Standard reference conditions, declarations of power, fuel and lubricating oil consumptions, and test methods. IS
13、O 3258:1976, Air distribution and air diffusion Vocabulary. 3 Definitions For the purposes of this International Standard, the definitions given below, together with those in ISO 31-1, ISO 31-3, ISO 31-4, ISO 3046-1 and ISO 3258, apply. 3.1 engine room: Space containing main propulsion machinery, bo
14、iler(s), diesel generator(s) and major electrical machinery, etc. -,-,- ISO 8861:1998(E) ISO 2 3.2 ventilation: Provision of air to an enclosed space to meet the needs of the occupants and/or the requirements of the equipment therein. 3.3 service standard power: The continuous brake power which the
15、engine manufacturer declares that an engine is capable of delivering, using only the essential dependent auxiliaries, between the normal maintenance intervals stated by the manufacturer and under the following conditions: a) at a stated speed at the ambient and operating conditions of the engine app
16、lication; b) with the declared power adjusted or corrected as determined by the manufacturer to the stated ambient and operating conditions of the engine application; c)with the maintenance prescribed by the engine manufacturer being carried out. ISO 3046-1:1995 See A.1 in annex A of ISO 3046-1:1995
17、. 4 Design conditions The outside ambient air temperature shall be taken as + 35 C. Temperature rise from air intake to air passing from the engine room up to the casing entrance shall be max. 12,5 K. The capacity of the ventilation plant should be such as to provide comfortable working conditions i
18、n the engine room, to supply the necessary combustion air to the diesel engine(s) and boiler(s), and to prevent heat-sensitive apparatus from overheating. In order to meet these requirements, the air should be distributed to all parts of the engine room, so that pockets of stagnant hot air are avoid
19、ed. Special considerations should be given to areas with great heat emission and to all normal working areas, where reasonably fresh and clean outdoor air should be provided through adjustable inlet devices. When arranging the air distribution, all normal conditions at sea and in harbour for in-serv
20、ice machinery shall be taken into account. 5 Airflow calculation 5.1 Total airflow The total airflow Q to the engine room shall be at least the larger value of the two following calculations. a:Q = qc + qh as calculated according to 5.2 and 5.3 respectively. b:Q = 1,5 x qc, i.e. the airflow for comb
21、ustion + 50 %. The total airflow to the engine room shall not be less than the airflow for combustion engine(s) and boiler(s) plus 50 %. ISOISO 8861:1998(E) 3 Combustion air to, and heat emission from, all equipment installed within the casing and funnel shall not be taken into account. The calculat
22、ions shall be based on simultaneous maximum rating of main propulsion diesel engine(s), diesel generator engine(s), boiler(s) and other machinery under normal sea conditions, and on a temperature increase of 12,5 K. The calculations should, to the greatest possible extent, be based on information fr
23、om the manufacturers. Guidance values given in this International Standard should be used only when manufacturers information is not available. In order to ensure satisfactory air distribution, combustion air to, and heat emission from, main propulsion diesel engine(s), diesel generator engine(s), g
24、enerator(s), boiler(s), and possibly other machinery with considerable heat emission, shall be calculated separately including other conditions as necessary. Spaces separated from the main engine room, such as individual auxiliary engine rooms, boiler rooms and separator rooms, shall also be calcula
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 8861 1998
![提示](https://www.31doc.com/images/bang_tan.gif)
链接地址:https://www.31doc.com/p-3779651.html